Enamel Pin Backing Types: Which Clutch or Fitting to Choose
Choosing an enamel pin backing is the part of the spec most buyers leave to the last email, and it is the part your wearers notice first. The pin front can be flawless, clean lines, tight enamel, good plating, and still feel cheap in the hand if the fitting behind it slips, spins or slides off a jacket lapel.
So let's fix that. Here is a plain walk through the fittings used across the trade, which wearers each one suits, and how the choice quietly shapes your packaging, freight and unit cost. Where our own workshop has a view, we say so.
Why the back matters more than the front
A lapel pin is wearable hardware, not a sticker. Wikipedia's entry on lapel pins gives the pin back its own treatment, which tells you the trade sees the fitting as a component in its own right. Your customers do the same thing without thinking about it. The design sells the pin. The back decides whether it survives a school term, a trade show or a wet Saturday at the racecourse.
Three failures show up again and again. The pin drops off and is lost. The pin tilts forward because a single post cannot hold a heavy badge flat against the chest. Or the attachment damages the garment: a hole in a knit, a magnet that creeps, a brooch pin that snags a lining. All three are backing problems, not design problems.
The six fittings you will meet
Butterfly clutch
The default. A small metal clutch with two spring wings you pinch to release. It is the cheapest fitting on the market, which is why it sits on most stock pins and most giveaway orders. Grip is fine on a shirt or a flat jacket lapel and weaker on thick wool or slippery synthetics. The wings bend if someone yanks instead of pinching.
If you need thousands of pins at a low unit price and the pin is light, this is the sane starting point.
Rubber clutch pin back
A black rubber or soft PVC barrel that grips the post by friction. Military and police style badges have used these for decades, and for good reason: a decent rubber clutch holds tight, does not scratch the plating behind the badge, and feels deliberate in the hand. Many buyers upgrading from a butterfly clutch land here.
Two things to watch. The clutch needs a post of the right diameter, because a thin post wears loose over months of use. And the barrel sits proud of the fabric, so it needs a little more room on a backing card and inside a slim gift box.
Locking pin back
A metal barrel clutch with a spring collar, sometimes with a small screw or catch that locks the post. This is the fitting for pins that travel: lanyards, tote bags, backpacks, caps, anything that gets knocked in a crowd. It costs more per piece than a butterfly clutch and weighs a bit more, and for high value pins that is usually the right trade.
Magnetic back
Two magnets, one behind the garment and one on the pin. No hole at all, which is the whole point for silk, leather, jerseys and uniforms where a puncture is not allowed. Good magnets hold a normal sized pin flat and let the wearer reposition it in seconds.
Bad magnets slide or are impossible to separate with cold fingers. Very heavy 3D badges usually need more magnet than is comfortable, so keep magnetic backs for lighter pieces or ask for a stronger grade. Worth a mention in your listing: magnets should be kept away from medical devices and from anyone with an implanted pacemaker.
Safety pin
A hinged safety pin fixed to the back, sometimes on a swivel so the badge hangs straight. Cheap, familiar, and effective on heavy fabric or on items that get pinned and unpinned all day. It does sit higher off the surface than a clutch, and a long safety pin can catch on loose knitwear. For a badge that will be moved between garments constantly, it is hard to beat on simplicity.
Brooch pin
A long bar pin with a catch, often a double pin for large pieces. This is the fitting for name badges, sash pins, ceremonial and commemorative pieces, and anything with real weight. It handles thick wool coats and sashes that a single butterfly clutch would fail on. Expect more assembly time and a higher unit price, and expect the pin to sit noticeably off the fabric.
Side by side
| Fitting | How it holds | Best for | Watch out for |
|---|---|---|---|
| Butterfly clutch | Two spring wings pinch the post | Giveaways, light pins, shirts and flat lapels | Bends if forced; weak on thick wool |
| Rubber clutch | Friction grip on the post | Uniforms, daily wear, badge style pins | Needs correct post diameter; bulkier on cards |
| Locking pin back | Spring collar or screw locks the post | Bags, lanyards, caps, high value pins | Higher unit cost and more weight |
| Magnetic back | Two magnets clamp the fabric | Jerseys, silk, leather, no hole allowed | Slips if too weak; hard to separate if too strong |
| Safety pin | Hinged clasp through the fabric | Heavy fabric, pins moved often | Sits high; can snag loose knits |
| Brooch pin | Long bar with a catch, often double | Large badges, name badges, sashes | Most assembly time; leaves a bigger hole |
Matching the fitting to the wearer
Forget the catalogue for a second and picture the actual person. That answers most of it.
- Conference giveaway. Light pin, low unit price, worn for two days. Butterfly clutch or rubber clutch, on a printed card.
- School, club or charity pin. Worn weekly by people who are not careful. Rubber clutch holds better than most cheap butterflies for a small step up in cost.
- Security, army or police style badge. Rubber clutch as standard, locking back for the premium version.
- Race or event finisher pin. Butterfly clutch works, but if it pins to a technical running top or a cycling jersey, the wearer may not want a hole in a piece of kit. Magnetic is worth pricing.
- Retail souvenir pin. Butterfly clutch, packed on a backing card, because the buyer wants to see the pin, not the fitting.
- Large 3D badge or name badge on a suit. Brooch pin, or two posts with locking backs so the badge cannot rotate.
- Pin that lives on a bag or lanyard. Locking pin back. No debate.
One more question to settle early: does the wearer mind a hole in the garment? If the answer is no, your options narrow fast, and the fittings that leave holes are all off the table.
How the backing changes packaging and landed cost
The fitting is a small line in the cost sheet, but it moves two other numbers.
The first is unit cost. Butterfly and rubber clutches are the budget end. Locking backs, magnetic pairs and brooch pins cost more, and a second post adds a little on both the fitting and the assembly. That extra can be cents per piece, and in a run of twenty thousand it is a real line item. It is also the difference between a pin that lasts and a pin your customer complains about. A cheap clutch on an expensive hard enamel pin is a false economy, and a premium locking back on a throwaway giveaway is money burned. Our fuller breakdown of how a pin quote is built sits in the custom pin cost guide.
The second is packaging. A backing card needs the clutch to be pushed onto the post, or bagged loose, and your choice changes the assembly step at the packing table. Deeper barrels (rubber, locking, magnetic) need a slightly thicker poly bag or an insert tray in a gift box. Magnets in bulk cling to each other and to any steel on the packing bench, which slows the line down. If you want the pin to arrive with the clutch already on and the card ready for retail, say so in the brief, because it changes how the bag is filled.
The metal under the plating sets the cost floor, the fitting nudges it. Our technical notes cover this in detail: brass, zinc alloy and iron each behave differently, and brass is a common substrate for die struck and photo etched work because it takes fine detail and plates cleanly. The fitting you pair with it should match that level of care.
Small spec mistakes that cost real money
- "Butterfly clutch" with no post length. A short post will not clear a thick lapel or a folded card. Ask for the post to be sized to the intended garment.
- Two posts on a tiny pin. Below roughly 20 mm there may be no room. The factory will either use one post or a different fitting.
- Magnet on a heavy 3D badge. It will slide on a gym top. Overbuild the magnet or change the fitting.
- No colour specified for the clutch. Black rubber behind a polished gold back is a different product to nickel. State it.
- Forgetting to say whether the clutch ships attached. It changes packing time and how the parcel survives transit.
- Mixing fittings across one order. Fine, but each variant is a separate line for the packing team. Tell your supplier which counts go where.
How we handle attachments
Our production runs in twelve steps, and attaching the fitting is one of them, sitting between cutting the shape and polishing. The backing is not an afterthought bolted on at the end. It is a step with its own handling.
We fix attachments to order. The fitting is agreed with your artwork and matched to the post diameter, the weight of the pin and the garment it will sit on, then fitted during the run. That is more useful than any catalogue list, because two pins that look identical can need different backs, and the answer comes out of the design. If your design calls for something less usual, our purchasing team sources special fittings and packaging rather than asking you to hunt for a supplier.
Ask early. Tell us the wearer, the garment and whether a hole is acceptable, and we will confirm which fitting suits your design alongside the mould quote, so you see the cost difference before you commit.
What we do not do is pretend one fitting fits everything. It does not, and a supplier who says so has not thought about your customer.
Ready to start an order
Send your design and we will quote the fitting properly. Here is what helps most:
- Artwork in Adobe Illustrator or CorelDRAW if you have it, with colours as Pantone Solid Coated references. If you only have a sketch or a photo, our design team can work from that.
- The garment and the wearer (school uniform, race jersey, suit lapel, tote bag).
- Whether a pin hole is acceptable.
- Rough quantity, and whether the pin will be handed out or sold.
Design work is free, custom orders are accepted regardless of order size, and a sample usually takes 3 to 8 days with bulk production at 7 to 15 days depending on the item. Take a look at the custom lapel pins we make, then get in touch through the contact page or email [email protected]. Tell us the fitting you are leaning towards and we will tell you honestly whether it is the right one.
Frequently asked questions
What is the most common enamel pin backing?
The butterfly clutch. It is the cheapest metal fitting, it works on most light pins and flat lapels, and it is what most stock pins ship with. Rubber clutches are the usual upgrade for uniforms and daily wear because they grip the post more firmly and do not scratch the plating.
Should I choose a rubber clutch pin back or a locking pin back?
Choose a rubber clutch for a badge worn on a shirt, a jacket or a uniform and taken off occasionally. Choose a locking pin back for anything that travels on a bag, lanyard, cap or backpack, where knocks and snags are the real risk. Locking backs cost more per piece and weigh a little more.
Can a magnetic pin back damage clothing?
No holes, which is why buyers pick it for jerseys, silk, leather and uniforms. The risks are different: a weak magnet can slide out of position, a very strong one is hard to separate, and magnets should be kept away from medical devices such as implanted pacemakers. Keep magnetic backs for lighter pins or ask for a stronger grade.
Does the backing type change the price of a custom pin?
Yes, though it is a smaller factor than size, metal, colour process and quantity. Butterfly and rubber clutches sit at the budget end. Locking backs, magnetic pairs and brooch pins cost more and add assembly time, and a second post adds a little more. Ask for the fitting to be listed as its own line on your quote so you can compare before ordering.
