How Much Do Custom Pins Cost? 7 Factors Behind Your Quote
Ask five factories how much do custom pins cost and you'll get five different numbers, because custom pins cost is a calculation, not a catalogue figure. Size, craft, colour count, metal, plating, backing and quantity all move the number, and so does something less visible: how much of the work is done by hand. Here are the seven factors behind your quote, roughly in the order they hit the price.
Seven factors, one quote
A lapel pin is a small decorative object worn on a jacket, lanyard or bag, and the Wikipedia entry on lapel pins covers the history. For budgeting, the useful part is simpler. A pin is a manufactured metal part, not a print. Someone cuts a mould, strikes or casts the metal, polishes it, plates it, fills colour and bakes it. Each of those steps costs money, and each choice you make shifts the total.
Which is why a supplier who quotes you a firm unit price before seeing your artwork is guessing. So are you, if you budget from a blog post alone. Get the factors straight and the quotes you collect will actually be comparable.
1. Size: how much metal you are paying for
Price climbs with surface area and thickness. A bigger pin uses more metal, needs a larger mould, takes longer to press or cast, swallows more enamel and spends more time on the polishing wheel. Many of the pins we make sit around 3 cm across, and that size keeps most logos readable without drama. Push past 4 or 5 cm and you start paying for weight as much as for detail. Size also changes what craft makes sense: thin sheet such as the 0.8 mm brass used for etched pins keeps a large badge light enough to wear all day.
2. Craft: the single biggest lever
Most of the price gap between two quotes for the same artwork lives here. The common options, roughly from most to least expensive:
- Hard enamel (cloisonné). Powdered glass-like colour is hand-filled and fired one colour at a time at 1,700°F for two to four minutes, then hand polished and plated so the surface is smooth and flush. Slow, skilled, and the colour holds.
- Imitation hard enamel. Synthetic pigment that looks close to cloisonné for less money, with faster production and a wider colour range. Also called soft cloisonné or Epola.
- Soft enamel. Colour sits in the recesses so you feel the metal ridges under your thumb. Hand-filled and baked to set the colour. Cheaper than hard enamel and the usual pick for detailed or 3D designs.
- Iron soft enamel. Same idea in iron. Lower unit price because the metal costs less and polishing and plating take less time.
- Photo etched. Your design is transferred from a photographic negative and eaten into the metal with chemicals, a photochemical machining process. Good value on large or light pins. No 3D, because the etch is shallow.
- Printed. Silkscreen or offset (CMYK) printing under an epoxy coat. No enamel filling and no metal lines between colours, which makes it the sensible option for big quantities on a tight deadline.
Weighing up the first two? Our comparison of hard enamel vs soft enamel pins goes deeper into the trade-offs. You can also browse finished work on our custom lapel pins page.
3. Colours: each one is a step
In hard enamel, every colour is a separate fill and a separate trip through the oven. In silkscreen printing, every colour carries a set-up charge. So a four-colour logo and a nine-colour illustration are not the same job, even at the same size on the same metal.
Two easy savings. Let the plated metal stand in for a colour, since white or gold areas often work well bare. And simplify gradients. Offset printing lays down CMYK in one pass, so photographic or gradient-heavy artwork is frequently cheaper printed than enamelled.
4. Metal
Four families cover most pins. Zinc alloy casts cheaply and takes complex shapes. Copper and brass feel heavier and hold a fine stamp, though the raw metal price moves with the market (the brass entry explains what the alloy actually is). Iron is the budget route. Stainless steel 304 or 316 is hard, corrosion resistant, and worth the extra when the pin will live outdoors on a backpack.
Metal choice also decides how the edges look. Iron pins often go unpolished unless you ask, and that roughness is one of the quick ways to tell them from brass. A magnet is the other: if it sticks, you are holding iron.
5. Plating
Plating is an electroplating step, and it is more than a colour choice. Gold, nickel, copper, bronze, antique and satin finishes all sit in the standard range. Two-tone work, antique effects and heavy hand polishing add operations, and operations cost.
One practical note. Factories often plate iron pins in bronze to imitate gold, or nickel to imitate silver, to hold the price down. That is fine for a giveaway and less fine for a piece that has to look premium. We run our own plating line with pollution treatment systems, and hold a Green Label Enterprise award from the local government. Keeping plating in house makes this part of the quote easier to control.
6. Backing and packaging
Two small line items that quietly change the unit price. On the back, a butterfly clutch is the default and the cheapest. Rubber clutches, locking clasps, safety pins, magnets and adhesive backs all cost more. A locking clasp is worth it for collector pins that get worn often and lost rarely. Our guide to enamel pin backing types lays out the options side by side.
At the front end, a plain poly bag costs almost nothing. An OPP bag, bubble bag, printed backing card or gift box adds real money per piece. If you are mailing a few thousand pins in envelopes, skip the box. If a small batch is going to sponsors or speakers, the box earns its keep.
7. Quantity and repeat orders
Mould tooling, artwork set-up and machine set-up are fixed costs. Spread them over more pins and the unit price falls. That is the honest reason a small run costs more per piece, and no amount of negotiation changes it.
Repeat business is where the maths gets friendly. Same design, same mould, nothing new to cut. We keep moulds for 2 years, so reorders of an existing design carry no mould fee. If you suspect a design will come back next season (annual club pin, race series, staff anniversary), say so at quoting stage. It changes what cheap means across a run of repeat orders.
The seven factors at a glance
| Factor | Pushes the price down | Pushes the price up |
|---|---|---|
| Size | Around 3 cm, moderate thickness | Large pins, thick metal, heavy weight |
| Craft | Iron soft enamel, photo etched, printed at volume | Hard enamel, heavy hand polishing, 3D relief |
| Colours | Few fills, metal left bare | Many enamel colours, extra screen set-ups |
| Metal | Iron, zinc alloy | Copper, brass, stainless 304 or 316 |
| Plating | Single standard finish | Two-tone, antique, satin, extra polishing |
| Backing and packing | Butterfly clutch, poly bag | Locking clasp, gift box, printed card |
| Quantity | Larger runs, reorders on the same mould | Small runs, a fresh design every time |
How to save money without hurting quality
Some cuts are invisible on the finished pin. Some are not. These sit in the first group.
- Cut colours, not craft. Four enamel colours on soft enamel will look better than nine colours on a craft that cannot hold them cleanly.
- Use the metal as a colour. Bare gold or nickel areas read as intentional design, not as a shortcut.
- Match the backing to the use. Butterfly clutches are fine for a 5K finisher pin. Save locking clasps for the pin people keep.
- Skip 3D on large designs. A big flat or etched pin is lighter, cheaper to ship and less likely to snag.
- Bundle designs into one order. Three designs placed together often beat three separate small orders because the fixed costs only land once.
- Standard plating over two-tone. Antique and dual finishes are lovely on a premium pin and hard to justify on a giveaway.
- Plan for the reorder. Keep the artwork and mould spec on file and order again inside the two year window.
The cheapest pin is the one you don't have to remake. A rushed artwork approval, a colour brief that says "royal blue" with no Pantone reference, a 3D concept that needed to be 2D at 3 cm: those mistakes cost a whole run, not a few cents. Spend your time on the proof instead. Our notes on how to design a lapel pin and the production process will help you spot problems early.
How to start an order with us
Send us the artwork as Adobe Illustrator or CorelDRAW, or a clean high-resolution file, plus your size, quantity, craft preference, Pantone Solid Coated colour references, backing and packaging. Design work is free, and we reply within 8 hours during the working week, with sales online around the clock.
Samples usually take 3 to 8 days. Bulk production runs 7 to 15 days depending on the item. Payment is by T/T, L/C or PayPal, and we accept OEM and ODM work, trade and wholesale orders, and customisation at any order size. Small orders are welcome; that is not a polite fiction here.
Email [email protected], call or message +86 181 2281 1289 on WhatsApp, or use the contact page. You will get a quote broken down by the factors above, so you can see exactly what you are paying for and what to change if the number is not where you need it.
Frequently asked questions
How much do custom pins cost?
There is no single figure. Your quote depends on seven factors: size, craft, number of colours, metal, plating, backing and packaging, and quantity. Two pins with the same artwork can land far apart if one is hard enamel with a gift box and the other is iron soft enamel in a poly bag. Send your specs and artwork for a real number.
Is hard enamel more expensive than soft enamel?
Yes, generally. Hard enamel colour is hand-filled and fired one colour at a time, then hand polished and plated flush, which takes more time and skill. Soft enamel fills the recesses and is baked, so it costs less and also suits detailed or 3D designs better.
Do I pay the mould fee again when I reorder?
No. Reorders of the same design carry no mould fee, and we keep moulds for 2 years. If you expect an annual pin, a race series or a recurring staff award, mention it when you first order so the design and tooling are set up for a repeat run.
What is the cheapest way to make a large quantity of pins?
For big runs with a short deadline, printed pins (silkscreen or offset with an epoxy coat) usually beat enamelled pins, and photo etched pins are economical for large flat designs. Iron soft enamel is the budget choice in the struck family. Ask your supplier to price two or three options on the same artwork before you decide.
